Repiping & Whole-Home Pipe Replacement in Loveland, CO
Recurring leaks, rusty water, or falling pressure throughout the house usually means the pipe material itself is failing. A whole-home repipe fixes the actual cause.
When It's Not Just Another Repair
Leaks In Different Spots
A new leak every few months in a different part of the house.
Rusty Water Sitewide
Discolored water from multiple fixtures, not just one.
Falling Water Pressure
Pressure dropping gradually throughout the whole house.
Visible Pipe Corrosion
Green or white corrosion on exposed galvanized pipe.
A Repair Doesn't Fix Failing Pipe Material
Most homeowners call about the symptom directly in front of them, a leak under the kitchen sink, then a different leak in the bathroom wall a few months later, treating each as its own unrelated repair. When those calls keep coming from the same house, the actual problem usually isn't any single fitting or joint. It's the pipe material itself, most often aging galvanized steel, corroding from the inside out along its entire length. Fixing the leak in front of you doesn't touch the corrosion happening everywhere else in that same pipe run, which is why the leaks keep showing up somewhere new.
Homes built roughly before the 1970s are the ones we see this in most often around Loveland, since galvanized steel was the standard supply pipe material through that era before copper and later PEX took over. A galvanized line doesn't fail all at once. It narrows gradually as rust builds up on the inside of the pipe wall, which is why falling pressure often shows up gradually over a year or two rather than as a single sudden event. That makes it easy to attribute to something else at first.
Another Leak In A New Spot?
It might be the pipe material itself. Let's find out.
Whole-Home Or Just The Worst Sections
A full repipe replaces every supply line in the home with new PEX piping, which is the right call when galvanized pipe throughout the house is showing the same age and corrosion pattern. A partial repipe, replacing just the worst-affected sections, sometimes makes sense when the rest of the home's piping is a newer material or in noticeably better condition, though it doesn't eliminate the chance of another failure in an untouched section down the line.
Depends heavily on home size, number of fixtures, and how accessible the existing pipe runs are. Exact quote after an on-site walkthrough.
How A Repipe Project Works
Assess
Walk through the home to map existing pipe material and condition.
Quote
Flat price for full or partial repipe before work begins.
Repipe
New PEX run room by room, water shut off only in the active area.
Test
Full pressure and leak test at every fixture before we finish.
Repiping Historic Downtown And West Central Loveland
Loveland dates to the 1870s, and the blocks around Historic Downtown and West Central Loveland hold some of its oldest housing. Homes there were plumbed before PEX existed, and original galvanized or early copper supply lines are the most common reason homeowners ask about repiping. Homes in newer areas like Centerra rarely need it, so a pressure and flow test first tells us whether you need a full repipe or just a section.
Galvanized, CPVC, And Replacing Only The Hot Side
Owners think about repiping for different reasons. Some have galvanized pipe that is rusting from the inside. Others have CPVC that has turned brittle and want it replaced before it cracks. A few only need the hot water lines redone.
Replacing Before The Failure
Waiting for a burst is the costly way to learn that the pipe is done. A walk-through that checks pipe material, shutoffs, and pressure can show how much life remains. A burst that has already happened is handled on the burst pipe page.
Hot Side Only, Or The Whole House
Hot lines tend to fail first because heat speeds up wear. Replacing only those runs can be a staged plan when the cold side is sound. Ask for a price on both options so the difference is visible.
Routes Through The Attic
Routing new lines through the attic or walls can avoid cutting a slab. This often comes up after a leak is found under the floor, as described on the slab leak page. Access, ceiling height, and insulation affect labor, so expect the quote to list each.
Repiping Questions From Loveland Homeowners
One leak in one spot is usually just a repair. Leaks showing up in different spots over months, rusty water from multiple fixtures, or pressure dropping throughout the house all point to the pipe material itself failing, which is a repiping situation, not a series of unrelated repairs.
PEX is the standard choice for most residential repipes today, for its flexibility, freeze resistance, and long service life compared to the galvanized steel it usually replaces.
No, most whole-home repipes are completed with the home occupied, working room by room, though water will be shut off in a given area while that section's work is underway.
Most single-family homes take two to four days, depending on size and how accessible the existing pipe runs are.
Many owners do, especially when the pipe is old or has already failed once. A walk-through checks the condition and the likely failure points. The decision comes down to how much the pipe has aged and your tolerance for risk.
Yes, that can be a staged plan when the cold side is sound. Ask for a price for the hot side alone and for the whole house so you can compare.
Often, yes. New runs can be routed overhead and through walls to avoid cutting the floor. Access and ceiling layout decide how practical it is for your home.
Home age, bathroom count, pipe material if you know it, and any leak history. Photos of exposed pipe near the water heater help. With that, the dispatcher can explain the process and the next step.